wall industries, inc. 5 watson brook road exeter, nh 03833 08/01/2011 603-778-2300 www.wallindustries.com fax 603-778-9797 page 1 of 3 psm200 series single output 200 watt, u-chassis ac/dc medical power supply rev. d features active pfc single output high reliability rohs compliant medical approved 100% hi-pot tested 100% burn-in tested 90~264vac input range safety approvals, emc compliance short circuit, over load, and over voltage protected description the psm200 series of ac/dc medical power supplies provides 200 watts of continuous output power in a u-chassis design. all models have a single output, 90~264vac full range input, and active pfc. these supplies are designed to comply with ul60601-1, tuv en60601-1, and cb iec60601-1 requirements. all models are protected against short circuit, over load, and over voltage conditions. this series is 100% hi-pot and burn-in tested. specifications: psm200 series all specifications are based on 25c, nominal input voltage, and maximum out put current unless otherwise noted. we reserve the right to change specifications based on technological advances. input specifications input voltage range 90 ~ 264vac (full range) input frequency 47 ~ 63hz input current (rms) 3a at 90vac max. 1.5a at 264vac max. leakage current < 300a at 264vac output specifications output current see table output voltage see table voltage regulation 5% output power 200w max. ripple & noise (20mhz bw) (see note 1) see table hold up time > 16ms typical at 115vac and full load protection short circuit protection auto recover over voltage protection latch, ac recycle over load protection auto recover general specifications efficiency > 87% at 115vac and full load no load power consumption < 500mw power factor > 0.9 at 115vac/230vac and full load environmental specifications operating temperature 0c ~ +40c convection cooling storage temperature -10c to +85c humidity 20% ~ 90% mtbf >140,000 hours at full load and 25c ambient temperature physical specifications dimensions (l x w x h) 6.94 x 3.74 x 1.97 inches 176 x 95 x 50 mm weight 1.3 lbs (580g) safety & emi safety standards ul/c-ul ul60601-1, csa c22.2-no. 6060 1-1, tuv en60601-1, cb iec60601-1 emc standards en60601-1-2, fcc part 18 class b, en55011 class b, ce
wall industries, inc. 5 watson brook road exeter, nh 03833 08/01/2011 603-778-2300 www.wallindustries.com fax 603-778-9797 page 2 of 3 psm200 series single output 200 watt, u-chassis ac/dc medical power supply rev. d model selection guide model input voltage output voltage output current ripple & noise output power psm200a3-1y12 90 ~ 264 vac 12 vdc 16.66a 240mvp-p 200w psm200a3-1y16 90 ~ 264 vac 16 vdc 12.50a 300mvp-p 200w PSM200A3-1Y19 90 ~ 264 vac 19 vdc 10.53a 300mvp-p 200w psm200a3-1y20 90 ~ 264 vac 20 vdc 10a 300mvp-p 200w psm200a3-1y24 90 ~ 264 vac 24 vdc 8.33a 300mvp-p 200w psm200a3-1y36 90 ~ 264 vac 36 vdc 5.555a 300mvp-p 200w psm200a3-1y48 90 ~ 264 vac 48 vdc 4.166a 300mvp-p 200w notes 1. ripple & noise is measured at 20mhz bandwidth with a t antalum 10f in parallel with a 0.1f ceramic capacitor. derating curve 50c forced air cooling 12cfm 0 10 20 30 40 50 60 70 80 90 120 100 80 60 40 20 0 ambient temperature (c) load (%)
wall industries, inc. 5 watson brook road exeter, nh 03833 08/01/2011 603-778-2300 www.wallindustries.com fax 603-778-9797 page 3 of 3 psm200 series single output 200 watt, u-chassis ac/dc medical power supply rev. d mechanical drawing 6.93 (176.0) 0.24 (6.0) 0.30 (7.5) 3.74 (95.0) 0.91 (23.0) 1.97 (50.0) 0.79 (20.0) 0.79 (20.0) 0.91 (23.0) 1.85 (47.0) 0.30 (7.5) 0.30 (7.5) 0.24 (6.0) 0.24 (6.0) 0.24 (6.0) 0.24 (6.0) 0.30 (7.5) 0.30 (7.5) m3 (mounting holes) x 6 n l fg + unit: inches (mm)
|
